查詢結果分析
相關文獻
- Using a Combination of Sinus Augmentation and Titanium Mesh to Reconstruct Severely Resorbed Maxillary Ridge: A Preliminary Report
- 帶狀鈦網在結構物陰極防蝕的使用
- The Biological Complication after Guided Bone Regeneration Using Titanium Mesh and Synthetic Absorbable Membrane--A Case Report and Histological Results
- 鈦網合併骨移植材及可吸收再生膜在齒槽骨增高術中之運用:病例報告
- 利用鈦網和可吸收再生膜來施行引導骨再生術:病例報告
- 使用細孔洞鈦網和膠原再生膜重建失敗植體區的骨質再生:病例報告
- 利用鈦網金屬增進水平牙骨嵴寬度--病例報告
- 利用鈦網進行牙脊增進術在植牙手術的應用
- 利用3D列印技術直接或間接製作引導骨再生術之鈦網:病例系列
- Ridge Augmentation with Tent-pole Grafting Technique--A Case Report and Review of Literatures
頁籤選單縮合
| 題 名 | Using a Combination of Sinus Augmentation and Titanium Mesh to Reconstruct Severely Resorbed Maxillary Ridge: A Preliminary Report=合併鼻竇增進術與鈦網重建嚴重缺損的上顎齒槽脊:初步報告 |
|---|---|
| 作 者 | 蔡鎮州; 陳俊榮; 毛念平; 黃國精; | 書刊名 | 臺灣牙周病醫學會雜誌 |
| 卷 期 | 20:4 2015.12[民104.12] |
| 頁 次 | 頁264-275 |
| 分類號 | 416.96 |
| 關鍵詞 | 鈦網; 鼻竇增進術; 齒槽脊增進術; Titanium mesh; Sinus augmentation; Ridge augmentation; |
| 語 文 | 英文(English) |
| 中文摘要 | 本回溯性研究針對合併鈦網及鼻竇增進術來重建植牙所需齒槽脊的案例,探討其臨床治療結果及分析可能的影響因子。共計7位患者以電腦斷層掃描影像測量術前與術後齒槽脊的高度與寬度進行比較分析,並探討與固定骨釘有無之間的相關性。研究結果顯示,術前齒槽脊平均高度為6.5 ± 4.1 mm;術後齒槽脊平均高度為14.2 ± 3.5 mm;平均齒槽脊高度增加量為7.5 ± 4.7 mm。術前離預計牙骨質-牙釉質交接處(CEJ)3 mm的齒槽脊平均寬度為2.2 ± 2.6 mm;術後齒槽脊平均寬度為7.4 ± 1.9 mm;平均齒槽脊寬度增加量為5.2 ± 3.4mm。結論為以鈦網合併鼻竇增進術進行齒槽脊增進術在高度與寬度可達到具有統計學顯著差異的臨床齒槽脊增進效果,而與固定骨釘的使用無統計學上顯著關係。 |
| 英文摘要 | This retrospective study evaluated the clinical outcomes and the possible influence factors of ridge augmentation using the titanium mesh and sinus augmentation in seven patients. Preoperative and postoperative alveolar ridge heights and widths were measured with computed tomography imaging, and the correlations between the augmented bone and fixation screw were also analyzed. The result showed that the mean (± SD) preoperative and postoperative alveolar ridge height was 6.5 (± 4.1) mm and 14.2 (± 3.5) mm, respectively, and the mean (± SD) vertical augmentation was 7.5 (± 4.7) mm. The mean (± SD) preoperative and postoperative alveolar ridge width was 2.2 (± 2.6) mm and 7.4 (± 1.9) mm, respectively, and the mean (± SD) horizontal augmentation was 5.2 (± 3.4) mm. This study demonstrated that using a combination of sinus augmentation and titanium mesh resulted in a significant difference of the ridge height and ridge width between before and after surgery. However, there was no significant correlations with regards to fixation screws. |
本系統中英文摘要資訊取自各篇刊載內容。