查詢結果分析
來源資料
相關文獻
- 利用田口方法提高SUS 304不銹鋼線材之產量
- 伸線眼模之設計及加工技術介紹
- 伸線眼模最佳化設計方法
- Neural Network Procedures for Taguchi's Dynamic Problems
- 放電加工多重品質設計
- 放電加工製程參數最適化之研究
- 品質工程之田口式實驗設計
- Manufacturing Process Optimization of Short Glass Fiber Reinforced Polycarbonate Composites in Injection Molding
- 以田口分析法探討實驗參數對碳六十產率之影響
- 以田口方法探討不同氯化鈉濃度切削液對JIS SUS 304不銹鋼鑽削時之刀具壽命研究
頁籤選單縮合
題名 | 利用田口方法提高SUS 304不銹鋼線材之產量=Improving Productivity of SUS 304 Stainless Steel Using Taguchi Method |
---|---|
作者姓名(中文) | 戴國政; 李明賢; 林暉斌; 莊其峰; | 書刊名 | 技術學刊 |
卷期 | 20:4 民94.12 |
頁次 | 頁333-338 |
分類號 | 472.3 |
關鍵詞 | 田口方法; SUS304不銹鋼; 伸線; 眼模; Taguchi method; SUS 304 stainless steel; Drawing; Die; |
語文 | 中文(Chinese) |
中文摘要 | 金屬線材向來皆是各種工業中相當重要的一種材料,雖然近年來有從熔融金屬液製造金屬線材技術相繼問世,但目前產業界所生產的線材大都仍從鑄胚經輥軋、抽線機抽線等塑性加工程序而成;然而在抽線機的生產過程中,眼模減面率、伸線速度、潤滑油值等參數將影響線材產量、品質及生產成本。本文乃是利用田口方法,以L9 直交表的實驗配置進行試驗,探討SUS304 不銹鋼線材在不同參數製程下所得之線材產量,研究結果發現影響線材產量的因子為伸線油溫度及伸線速度。最後將伸線油溫度設定在45℃及伸線速度在620m/min 時,伸線產量增加約33.5% 。 |
英文摘要 | The metal wires are a key metal material and are applied widely in various industries. Although several new techniques have been invented to produce metal wires from melted metals, in the conventional manufacturing process, metal wires are produced from an ingot which passes through a rolling and drawing process. Some process parameters such as die reduction rate, drawing velocity and lubricant oil temperature may affect the production volume, quality and cost of the process of drawing. The purpose of this paper is to investigate the optimal process parameters for SUS 304 stainless steel to maximize wire production volume. Using Taguchi methods, an L9 orthogonal array is constructed. It is found that lubricant oil and drawing velocity are the controlling factors for improving productivity. Finally, the production volume increased 33.5% when lubricant oil temperature was set at 45℃ and drawing velocity was set at 620 m/min. |
本系統之摘要資訊系依該期刊論文摘要之資訊為主。